Muzzleloader Safety Rules

SPECIAL SAFETY RULES FOR MODEL 700™ MUZZLELOADERS
In addition to the Ten Commandments of Firearm Safety, there are several guidelines specific to black powder guns that hunters and shooters must observe at all times to ensure their safety and the safety of others. The following is a brief overview of these guidelines. For full details, thoroughly read your Model 700 ML instruction book.

MUZZLELOADING SAFETY RULES

  • NEVER smoke while using your muzzleloader or while near any quantity of black powder or PYRODEX®.
  • BEFORE LOADING, MAKE SURE THE FIREARM IS NOT ALREADY LOADED. To make sure it is unloaded, insert the ramrod provided with the rifle into the bore to the breech plug and note its position at the muzzle. It should be approximately 1/4 inch below flush with the end of the barrel if the rifle is not loaded. NOTE: Nothing can be attached to the ramrod while using it in this way. USE ONLY THE RAMROD PROVIDED.
  • ALWAYS CHECK AND CLEAR THE FLASH HOLE THROUGH THE NIPPLE BEFORE SHOOTING. ALWAYS CHECK THE BARREL FOR OBSTRUCTIONS BEFORE LOADING AND SHOOTING. Before checking for an obstruction, put the safety mechanism in the 'S' position and open the bolt assembly and remove the percussion cap and residue from the nipple. Water, snow, mud or any other material can obstruct the barrel and cause barrel damage.
  • USE BLACK POWDER OR PYRODEX ONLY TO LOAD YOUR MUZZLELOADING FIREARM. Never use even small amounts of smokeless powder, even if it is black in color. The use of any other propellant may cause injury or death to the shooter or bystanders and damage the firearm.
  • NEVER EXCEED THE MAXIMUM RECOMMENDED POWDER CHARGE CONTAINED IN YOUR INSTRUCTION BOOK. To do so could result in injury or death to the shooter or bystanders.
  • NEVER POUR POWDER DIRECTLY FROM A POWDER FLASK OR CONTAINER. A sudden powder ignition from a lingering spark could cause the entire flask to explode. Use an individual charge from a powder measure when loading your rifle. Read and follow your powder manufacturer's procedures for powder storage.
  • NEVER USE THE WRONG AMMUNITION COMPONENTS. Only use ammunition components that exactly match the caliber markings on your firearm and are meant to be used together. Use only pure lead or Remington brand loading components when shooting lubed conical bullets. Do not use any other lead alloys with lubed conical bullets as they may be too hard for proper and safe use in your muzzleloader.
  • WHEN LOADING, BE CERTAIN POWDER, PATCHES AND PROJECTILES ARE IN THEIR PROPER SEQUENCE AND THAT THEY ARE COMPLETELY SEATED AGAINST ONE ANOTHER. Serious personal injury or death can result if space is left between them. To provide a reference mark for future loadings, mark the ramrod at the muzzle once a projectile has been loaded to the proper depth. NOTE: Be sure to recheck the ramrod mark if you change loading components or alter the ramrod. See Picture 13 on page 15 of your Model 700 ML instruction book. Never attempt to shoot out a projectile that is not firmly seated against the powder charge or does not seat to the proper depth. Remove these projectiles following the instructions on pages 18 and 19 of your Model 700 ML instruction book.
  • ALWAYS USE COTTON PATCHING. The use of non-cotton patching could build up a static electric charge possibly creating a spark that could ignite the powder.
  • NEVER POUND THE RAMROD. Black powder and PYRODEX are impact sensitive and could ignite from impact. Keep the ramrod directly away from your face or body.
  • KNOW THE RANGE OF YOUR FIREARM. Muzzleloading projectiles have a range of more than one-half mile.
  • IF THE FIREARM FAILS TO FIRE, BE PREPARED FOR A HANGFIRE. Keep the muzzle pointed in a safe direction and wait no less than one full minute before opening the bolt. A spark may have reached the powder without any sound. The rifle could fire at any moment during this minute. If the rifle does not fire within a minute, carefully follow the directions on how to handle a misfire on pages 15 and 16 of the Model 700 ML instruction book.
  • RENDER YOUR FIREARM INOPERABLE WHENEVER YOU ARE NOT SHOOTING. Never place the percussion cap on the nipple until just before firing and remove it immediately if you do not fire. Never carry or store a loaded firearm in a building or a vehicle. Unload it by firing it into a suitable backstop before returning to your vehicle, entering a building, crossing or climbing up or down any obstacle that may prevent you from keeping full control over the firearm, such as a fallen tree, fence, treestand or slippery area. Failure to follow this rule may cause serious injury or death to the shooter or bystanders.
  • BLACK POWDER LEAVES HEAVY CORROSIVE RESIDUES. A thorough cleaning and lubing are absolute necessities before storage and prior to loading and shooting. Follow the cleaning instructions starting on page 19 of the Model 700 ML instruction book. Always carry loading and cleaning equipment with you in the field.
  • NEVER USE THE WEATHER SHROUD FOR REPEATED SHOOTING. It is intended for single shot usage. Always disassemble and clean the bolt assembly after shooting with the weather shroud. See page 22 of the Model 700 ML instruction book for bolt assembly cleaning instructions.
  • WARNING: Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition components may result in exposure to lead, a substance known to cause birth defects, reproductive harm, cancer and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.
     

WARNING: Failure to follow any of these muzzleloading safety rules may cause personal injury or death to the shooter or bystander and damage to property. Do not use a muzzleloader firearm until you fully understand and practice the Ten Commandments of Firearm Safety and the safety guidelines specific to black powder shooting, to your black powder firearm and to your black powder ammunition components. If you are unfamiliar with black powder firearms, seek professional instruction from a qualified organization such as the International Black Powder Hunting Association, National Muzzleloading Rifle Association, National Rifle Association or your State Hunter Safety program. If you have any questions about the safe use of a Remington black powder firearm, write to us at Remington Arms Company, Inc., Consumer Services, P.O. Box 700, Madison, NC 27025-0700, email us at info@remington.com, or call us at 1-800-243-9700.